Treon Gateway Configuration UI 1.0.0

Sep 6, 2023 · 4 minutes to read

Treon Gateway Treon Gateway 2 Treon Gateway in Protective Enclosure

This article shows the settings in the Treon Gateway Configuration UI 1.0.0 for Treon Aito Release 6.5.2 for Gateway.

Access Point Mode

To configure the Treon Gateway via the Configuration UI you need to turn the Treon Gateway into Access Point Mode and connect to it via a browser.

  1. Turn on the Treon Gateway and wait approximately 1 minute until the status light (A) turns from blue to green (connected) or red (not connected) to indicate that the gateway has fully booted.

  2. Press the configuration button (F) on the bottom of the gateway about 10 seconds until the status light (A) starts blinking. The gateway now becomes a Wi-Fi access point. (Please do not press the button for a full minute, as this will delete the data on the gateway.)

  3. Using your phone, computer, or tablet, connect to the access point: select the Wi-Fi network treongw1-serialnumber, where serialnumber is the serial number of your gateway.

  4. Enter your password. It has been provided separately with the Treon Gateway.
    Please Note: After selecting the correct Wi-Fi network, Windows 10 and Windows 11 may ask for a pin code as a primary access point password. Please use the “Connect using a Security key instead” option instead so you can enter the password. Remember to change the Wi-Fi password later.

  5. Open a browser on your phone, computer or tablet and go to address 192.168.0.1 in order to access the Treon Gateway Configuration UI.

Fig.: Press button F until status light A starts blinking

Configuration UI

The Configuration UI of the Treon Gateway let’s you change a variation of settings.

Fig.: Welcome to Treon Gateway Configuration UI

The Configuration UI offers a menu with the following items to choose:

Fig.: Configuration UI Main Menu

View Gateway Status

Here you can find information on your Treon Gateway, like the current Treon Aito Release for Gateway version, the cellular operator and if the maintenance connection is enabled.

Fig.: View Treon Gateway status information 1/2.
Fig.: View Treon Gateway status information 2/2.

 

Wi-Fi Settings

This setting is for connecting the Treon Gateway via a Wi-Fi network.

  1. Choose Add Wifi network and click Next. The Treon Gateway will now search for existing networks.
Fig.: Search for Wi-Fi networks.
  1. Select the Wi-Fi network you would like to connect to.
Fig.: Choose Wi-Fi network.
  1. Enter the password for the selected Wi-Fi network.
Fig.: Enter Wi-Fi password.
  1. Now the Treon Gateway will connect automatically to the selected Wi-Fi network.

 

Configure SIM settings

In the SIM settings you can check on the cellular operator, configure the APN, enable roaming and change the cellular profile.

Fig.: Configure the SIM settings of the Treon Gateway.

In case the SIM card was not recognized, the gateway will give you this message. Please check that the SIM card is valid for the Treon Gateway and was put properly into the SIM card slot.

Fig.: No SIM card could be identified by the Treon Gateway.
 

Configure LAN settings

Here you can set the DHCP client, change the ping settings and set the time of the Treon Gateway manually.

Fig.: Configure Treon Gateway Ethernet LAN settings.
 

Configure MQTT settings

Here you can change the Treon Gateway’s MQTT settings.

Fig.: Change Treon Gateway MQTT settings.
 

Change Gateway WiFi password

Here you can change the Wi-Fi password of the Treon Gateway. Please make sure to save the new password!

Fig.: Enter the new password and save.

 

Maintenance connection

This menu item lets you deactivate the maintenance connection of the Treon Gateway. As a default, the maintenance connection is enabled.

Fig.: Maintenance Connection Disabled.
Fig.: Maintenance Connection Enabled

 

View error log

Fig.: Main Menu - Treon Gateway error log.

 

Information

Here you can find information on the Configuration UI settings.

Fig.: Treon Gateway Configuration UI information.

 

Quit

In order to exit the Configuration UI and Access Point Mode, select Quit in the menu, or press and hold the configuration button (F) until the status light stops blinking.

Fig.: Quit the Configuration UI.

 

Treon Support

You still have questions? Our dedicated team of experts is happy to help you! Please contact Treon Support directly by e-mail.

Did you know? Treon offers Premium Support and Maintenance Packages for our customers. Get even more out of Treon and boost your sales - inquire now about features and prices!

   

configuration ui access point mode

Was this article helpful? Let us know.
Next

Last updated on Sep 6, 2023